DOI: 10.52150/2522-9117-2024-38-455-468

Razdobrieiev Valerii Huriiovych, Ph. D. (Tech.), Senior Researcher, Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine, Academican Starodubova Square, 1, Dnipro, 49107, Ukraine. ORCID: 0000-0001-7402-7992. E-mail: office.isi@nas.gov.ua

Kluychnikov Kyrylo Yuriiovych, Junior Researcher, Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine, Academican Starodubova Square, 1, Dnipro, 49107, Ukraine. ORCID: 0000-0003-2465-3244

Palamar Dmytro Hryhorovych, Junior Researcher, Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine, Academican Starodubova Square, 1, Dnipro, 49107, Ukraine. ORCID: 0000-0002-9503-3248

Leshchenko Oleksandr Ivanovych, Junior Researcher, Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine, Academican Starodubova Square, 1, Dnipro, 49107, Ukraine. ORCID: 0000- 0003-1877-8358

Ivanov Oleksandr Petrovych, Ph. D. (Tech.), Associate Professor, Leading Engineer, Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine, Academican Starodubova Square, 1, Dnipro, 49107, Ukraine. ORCID: 0000-0003-1259-6377

ANALYTICAL STUDIES OF THE INFLUENCE OF THE TECHNOLOGICAL PARAMETERS OF THE PROCESS OF PULLING THE STRIP THROUGH THE BENDING-STRETCHING DEVICE ON THE CHANGE OF THE ENERGY-FORCE PARAMETERS OF THE PROCESS

Abstract. It is impossible to imagine the modern development of technology without the use of metal products, including wire products, which are subject to high requirements in terms of variety and quality, and to the production processes, for example, wire of a fashioned profile, the flexibility of technology, high efficiency and economy, labor safety and automation. One of them is the process of drawing metal in roller dies, which combines the features of two methods of pressure metal processing – rolling and drawing. The main working tool when applying the drawing process in roller dies is a roller die with non-driven working rollers. The main drawback of the roller dies method is the presence of traction force. Stretching stresses in combination with a decrease in the plasticity of the metal during the drawing process can lead to the destruction of the rolled product. This limits the assortment of profiles, the total crimping in one of transition. It is possible to increase the plasticity of metal in two ways – thermal and mechanical. The thermal method, which is widely used in industry, requires significant energy consumption. At the same time, previous studies, which were carried out including in the ISI NASU, showed that it is possible to increase the plasticity of the metal by means of alternating sign deformation of the profiles, using, for example, equipment for straightening profiles or a scale breaker. The purpose of analytical research is to establish the dependence of the influence of the technological parameters of the drawing process in a roller drawing machine combined with the pulling of strips through a device for bending with tension (DBT) on the change of the energy parameters of the process based on the developed mathematical model. Analytical studies of the influence of the technological parameters of the DBT were carried out for the case of deformation of the initial workpiece of round cross-section with a diameter of 5.90 mm from low-carbon steel of the St.08 brand in a double-roll roller die with smooth rolls, combined with DBT in the conditions of the laboratory base of the pressure metal processing department of the Iron and Steel Institute of the Z.I. Nekrasov of NASU. On the basis of the revealed regularities, the dependences of the energy-force parameters of the process of drawing in a roller die, combined with the drawing of strip through the DBT, on the influence of the main technological parameters were obtained. It was established that an increase in the distance between of the axes rollers of the DBT at a constant value of the movement of the axis of the pressure roller of the DBT in the vertical direction leads to a decrease in the angle of coverage of the roller by the strip. It has been established that at a constant distance between the axes of the DBT rollers, when the amount of movement of the axis of the DBT pressure roller increases vertically, on the contrary, the values of the angle of coverage of the roller by the strip increase. It is shown that an increase in the number the rollers of DBR leads to an increase in both the pulling force of the strip and the normal component of the force acting on the trunnion of the rollers of the DBT. It was determined that the most significant influence of the height of the stretched strip and the radius the rollers of the DBT on the pulling force occurs in the range of relations R/h≤10. It was established that an increase in the total degree of preliminary deformation in the roller die and sign-changing deformation in the DBT of the strip leads to an increase in the value of the pulling force.

Key words: sign-changing deformation with stretching, tape type profiles, mechanical properties, bending and stretching roller device, roller die, pulling force, strip.

DOI: https://doi.org/10.52150/2522-9117-2024-38-455-468

For citation: Razdobrieiev, V. H., Kluychnikov, K. Yu.,Palamar, D. H., Leshchenko, O. I.,&Ivanov, O. P. (2024). Analytical studies of the influence of the technological parameters of the process of pulling the strip through the bending-stretching device on the change of the energy-force parameters of the process. Fundamental and applied problems of ferrous metallurgy, 38, 455-468. https://doi.org/10.52150/2522-9117-2024-38-455-468.

References

1. Gulko, V. I., Voitsekhovsky, V. A., & Grigoriev, A. K. (1989). Production of profiles and wire in roller dies. Udmurtia

2. Krasavin, B. N., Boyarshinov, M. I., & Polyakov, M. G. (1971). Ispol’zovaniye rolikovykh volok za rubezhom [Use of roller dies abroad]. Hardware production, 2, 11-16

3. Vydrin, A. V., Stern, A. A., Popov, Yu. N., & Barichko, B. V. (2004). Increasing the efficiency of drawing processes in roller dies. Proceedings of the Fifth Congress of Rolling. Chermetingzhiring

4. Khramkov, V. E., Stern, A. A., & Yakovleva K. Yu. (2015). On the issue of designing roller dies with offset pairs of rollers. Vestnik SUSU, 15(4), 128-134

5. Bitkov, V. V. (2004). Technology and machines for wire production. UrO RAN

6. Slavin, V. S., Norets, A. I., & Smushkevich, L. E. (2013). Effective technologies for the production of high-precision fashioned profiles. Prague

7. Razdobreev, V. G., Klyuchnikov, K. Yu., Leshchenko, O. I., & Palamar, D. G. (2022). Study of the influence of sign-changing bending of the strip on the change of deformation parameters and mechanical properties of metal. Casting. Metallurgy. 2022”: Materials of the XVIII International Scientific and Practical Conference, 220-223

8. Razdobreev, V. G., Kluychnikov, K. Yu., Leschenko, A. I., Palamar, D. G., & Vorobei, S. O. (2023). Production Efficiency of Ribbon-Type Sections by the Drawing Method in Doubled-Roll Roller Dies. Sci. innov., 19(6), 40-50

9. Razdobreev, V. G., Klyuchnikov, K. Yu., Leshchenko, O. I., & Palamar, D. G. (2023). Study of the influence of the main technological parameters of the drawing process in double roller drawing on the dynamic characteristics of the process. “Casting. Metallurgy. 2023”: Materials of the XIX International Scientific and Practical Conference, 376-379

10. Razdobreev, V. G., Klyuchnikov, K. Yu., Leshchenko, O. I., & Palamar, D. G. (2023). Mathematical modeling of the process of obtaining tape-type profiles from a round blank. “PROBLEMS OF MATHEMATICAL MODELING”: Materials of the All-Ukrainian scientific and methodological conference, 55-57

11. Razdobreev, V. G. Prikhodko, I. Yu., Kluychnikov, K. Yu., Palamar, D. G., & Leshchenko, A. I. (2023). The choice of the method of determining the energy parameters of the process of drawing the staffs through the bending-stretching device. Fundamental and applied problems of ferrous metallurgy, 37, 358-373

12. Tarnavsky, A. L. (1965). Power conditions for drawing using roller scale breakers. Steel, 2, 182-184

13. Zalazinsky, A. G. & Bitkov V. V. (1995). Calculation of the force of pulling wire rod through the descaling rollers. Steel, 8, 54-56

14. Kokovikhin, Yu. I. (1995). Tekhnologiya staleprovolochnogo proizvodstva. Tekhnika

Фундаментальные и прикладные проблемы черной металлургии
Logo