Фундаментальные и прикладные проблемы черной металлургии

DOI: 10.52150/2522-9117-2023-37-505-521

Uzlov Kostiantyn Ivanovych, D. Sc. (Tech.), Prof., Ukrainian State University of Science and Technologies, Lazariana Str., 2, Dnipro, 49010, Ukraine. ORCID: 0000-0003-0744-9890. E-mail: konst.uzlov@gmail.com

Repyakh Serhii Ivanovych, д.т.н., проф., Ukrainian State University of Science and Technologies, Lazariana Str., 2, Dnipro, 49010, Ukraine. ORCID: 0000-0003-0203-4135. E-mail: 123rs@ua.fm

Kimstach Tetiana Volodymyrivna, Junior Researcher, Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine, Academican Starodubova Square, 1, Dnipro, 49107, Ukraine. ORCID: 0000-0002-8993-201X. Ukrainian State University of Science and Technologies, Lazariana Str., 2, Dnipro, 49010, Ukraine. E-mail: 1375tatyana@gmail.com

Safronova Olena Anatoliivna, Junior Researcher, Ph. D. Student, Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine, Academican Starodubova Square, 1, Dnipro, 49107, Ukraine. ORCID: 0000-0002-4032-4275. E-mail: safronovaaa77@gmail.com

Mazorchuk Vladimir Fedorovich, Ph. D. (Tech.), Assос. Prof.,  Ukrainian State University of Science and Technologies, 2 Lazaryana St., Dnipro, 49010, Ukraine.  ORCID: 0000-0002-4115-9865

Bilyi А. P., Ph. D. Student, Ukrainian State University of Science and Technologies, Lazariana Str., 2, Dnipro, 49010, Ukraine. ORCID: 0000-0003-2905-7046

TRIBOTECHNICAL PROPERTIES OF BRO3A3 ALLOY UNDER DRY FRICTION CONDITIONS

Abstract. Currently, lead and tin bronzes are most often used for the production of bearings, which is due to their high level of tribotechnical properties and reliability in operation. At the same time, the ban in the European Union on the use of lead in any products led to the need to find environmentally safe bronzes with a similar or increased level of tribotechnical properties. A promising way to solve this problem is BrO3A3 bronze, the microstructure of which fully meets the requirements for bearing alloys. However, to date, the tribotechnical properties of BrO3A3 bronze have not been investigated. Therefore, the task of researching the tribotechnical properties of cast bronze BrO3A3 as a bearing alloy is urgent. The purpose of the work is to establish the values of relative wear resistance and friction coefficient, as parameters by which it is possible to recommend the use of cast bronze of the BrО3A3 brand as an antifriction material. Wear resistance tests according to the “disk-disk” scheme were carried out in accordance with the requirements of State and International standards on a mod machine. SMC-2 under a load of 45 kg (441 N) in friction-rolling conditions with a slip of 10% at room temperatures. Tribotechnical tests of the samples of the investigated bronzes according to the “ball-disc” scheme were carried out under dry friction-sliding conditions on the “Micron-tribo” friction machine in accordance with the International Standards DIN 50324 and ISO 20808. The microstructure was studied using a NEOPHOT 21 optical microscope with a magnification of up to 1000 times. According to the results of the study, it was found that compared to BrO5C5C5 and BrA9Zh3L bronzes, BrO3A3 bronze is characterized by a higher level of resistance to wear during dry rubbing, which is due to the presence of a hard but plastic phase in its structure β-Cu5Sn. The value of the coefficient of friction of BrO3A3 bronze coincides with the similar coefficient of BrO5C5S5 bronze and is lower than that of pure copper and bronzes of BrO8, BrA5 and BrA9Zh3L brands. At the same time, with an increase in the content of both tin (from 3 to 4% by mass) and aluminum (from 3 to 4% by mass), the coefficient of friction of BrO3A3 bronze decreases from 0.28 to 0.25. The research results are a reason to recommend BrO3A3 bronze as a tribotechnical material in friction nodes to replace not only lead bronzes and BrO5C5S5 bronzes, but also BrA9Zh3L bronzes.

Key words: bronze, wear resistance, friction, mass, phase, aluminum, tin, lead.

DOI: https://doi.org/10.52150/2522-9117-2023-37-505-521

For citation: Uzlov, K. I., Repyakh, S. I., Kimstach, T. V., Safronova, O. A., Mazorchuk, V. F., & Bilyi, А. P. (2023). Tribotechnical properties of BRO3A3 alloy under dry friction conditions. Fundamental and applied problems of ferrous metallurgy, 37, 505-521. https://doi.org/10.52150/2522-9117-2023-37-505-521

References

  1. Arzamasov, B. N., Makarova, V. I., & Muhin, G. G. (2003). Materialovedenie. Publishing house of MSTU named after. N.E. Bauman
  2. Lahtin, Yu. M. (1983). Materialovedenie i termicheskaya obrabotka metallov. Metallurgiya
  3. Merkulova, G. A. (2008). Metallovedenie i termicheskaya obrabotka cvetnyh splavov. Sib. feder. University
  4. Marrocco, T., Driver, L. C., Harris, S. J., & McCartney, D. G. (2006). Microstructure and Properties of Thermally Sprayed Al-Sn-Based Alloys for Plain Bearing Applications. Journal of Thermal Spray Technology, 15(4), 634-639
  5. Kryachek, V. M. (2005) Sintered metals and alloys friction Composites: Traditions and New Solutions (review). II. Composite  materials. Powder metallurgy and Metal Ceramics, 44, 1-2, 5-15
  6. Hreshta, V. L., Lysytsia, O. V., & Stepanova, L. P. (2014) Kolorovi metaly ta splavy na yikh osnovi. ZNTU
  7. Poluhin, M. S., & Kamynin, V. V. (2011). Vliyanie strukturnyh faktorov na tribotekhnicheskie svojstva antifrikcionnyh chugunov. Bulletin of Voronezh State Technical University, 7, 43-47
  8. Tavrov, V. I. (2012). K obosnovaniyu vybora materiala dlya podshipnika skol’zheniya. Faktory, opredelyayushchie vybor materiala. Electronic scientific and technical journal Engineering Bulletin, 12, 77- 48211/513921
  9. Gulyaev, A. P. (1986). Metallovedenie.Metallurgy
  10. Kіmstach, T. V., Uzlov, K. І., Rep’yah, S. І., & Solonenko, L. І. (2022) Optimizing the content of tin and aluminum in tin bronze according to the indicators of mechanical properties indicators. Metal science and thermal processing of metals, 2 (97), 41–54. https://doi.org/10.30838/J.PMHTM.2413.050722.41.858
  11. ASTM E3 – 11(2017) Standard Guide for Preparation of Metallographic Specimens
  12. Popilov, L. Ya., & Zajceva, L. P. (1963) Elektropolirovanie i elektrotravlenie metallograficheskih shlifov. Metallurgizdat
  13. Kovalenko, V. S. (1981). Metallograficheskie reaktivy. Metallurgizdat
  14. Bekkert, M., & Klemm, H. (1988). Sposoby metallograficheskogo travleniya: spravochnoe izdanie. Metallurgizdat
  15. Goncharov, O. A., Vasil’єva L. V., & Yunda, A. M. (2020). Chisel’nі metodi rozv’yazannya prikladnih zadach  navch. posіb [Numerical methods of solving applied problems: teaching. manual]. Sumy State University
  16. Uzlov, K. І., Rep’yah, S. І., Dzyubіna, A. V., Kіmstach, T. V., & Movchan, O. V. (2019) Analіz vіdpovіdnostі normativnih vimog do alyumіnієvih bronz zakonomіrnostyam strukturoutvorennya v sistemі Su-Al [Analysis of the compliance of regulatory requirements for aluminum bronzes with the patterns of structure formation in the Cu-Al system]. Theory and practice of metallurgy, 5 (122), 55–63. https://doi.org/10.34185/tpm.5.2019.07
  17. Kіmstach, T. V., Uzlov, K. І., Solonenko, L. І., Rep’yah, S. І., Hrichikov V., Bіlij, O. P., Bіlij A. P., & Іvanova, L. H. (2021). Doslіdzhennya vplivu domіshok v bronzі BrO3A3 na її mekhanіchnі vlastivostі [Study of the effect of impurities in BrO3A3 bronze on its mechanical properties]. Theory and practice of metallurgy, 4 (129), 41–47. https://doi.org/10.34185/tpm.4.2021.05

No widgets added. You can disable footer widget area in theme options - footer options

Фундаментальные и прикладные проблемы черной металлургии
Logo